t2200 craftsman mower manual

The Craftsman T2200 is a 22-horsepower riding lawn mower with a 46-inch cutting deck, hydrostatic transmission, electric start, and a 2.5-gallon fuel tank. It features a Briggs & Stratton engine, a 12-volt battery, a cup holder, a high-back seat, and a mulching kit option. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Setup 3. First-Time Operation 4. Specifications 5. Controls and Settings 6. Attachments & Accessories 7. Mowing Operation 8. Safety Features 10. Care & Maintenance 11. Regulatory Information 12. Troubleshooting

Features at a Glance

Key components: 22 HP Briggs & Stratton engine, 46-inch cutting deck, Hydrostatic transmission, Electric start, 12V battery, High-back seat, Cup holder, Mulching capability.

Feature	Description
Engine	22 HP Briggs & Stratton, single-cylinder, air-cooled
Cutting Deck	46-inch stamped steel, 3-blade system
Transmission	Hydrostatic, foot-pedal controlled
Starting System	Electric key start with 12V battery
Fuel Tank	2.5-gallon capacity
Seat	High-back, adjustable for operator comfort
Cutting Height	Adjustable from 1.5 to 4 inches
Drive System	Rear-wheel drive
Blade Engagement	Electric PTO (Power Take-Off) switch
Mulching Kit	Optional, converts to mulching mode

Assembly & Setup

Unpack and inspect all parts. Assemble on a flat, stable surface.

Install steering wheel: Align and tighten bolt.
Attach seat: Mount using provided bolts and washers.
Connect battery: Attach red (+) then black (-) terminals.
Install cutting deck: Lower deck onto mounting points and secure with pins.
Check tire pressure: Inflate to 10 PSI (front) and 12 PSI (rear).

WARNING! Mower is heavy; use assistance during assembly. Ensure all bolts are tightened securely.

First-Time Operation

Perform pre-operation checks before starting.

Check oil level: Ensure oil is at full mark on dipstick.
Add fuel: Use fresh unleaded gasoline (87 octane or higher).
Adjust seat: Position for comfortable reach to controls.
Set cutting height: Use deck lift lever to desired height.
Start engine: Insert key, set parking brake, turn to START.
Engage blades: Press PTO switch after engine is running.

CAUTION! Never operate on slopes greater than 15 degrees. Keep hands and feet away from moving parts.

Specifications

Engine: 22 HP Briggs & Stratton, 724cc.
Cutting Width: 46 inches.
Transmission: Hydrostatic, infinite forward/reverse speeds.
Fuel Capacity: 2.5 gallons.
Battery: 12V, 180 CCA.
Cutting Height Range: 1.5 to 4 inches (6 positions).
Weight: Approximately 500 lbs.
Tire Size: Front 15x6.00-6, Rear 20x10.00-8.
Warranty: 2-year limited warranty.

Controls and Settings

Operator station includes: Ignition key, Hydrostatic drive pedal, Brake pedal, PTO switch, Deck lift lever, Parking brake, Throttle control, Cup holder.

Dashboard: Ignition switch, Hour meter, Battery indicator light.

Cutting Height: Adjust via deck lift lever (1.5 to 4 inches). Speed Control: Hydrostatic pedal - press forward to go forward, reverse to go backward. Throttle: Set to FAST for mowing, SLOW for idling. Parking Brake: Engage before dismounting.

Attachments & Accessories

Optional: Mulching kit, Bagging system, Snow blade, Tow-behind spreader.

Turn off engine and remove key before installing attachments.
Follow attachment-specific instructions for mounting.
Ensure all pins and bolts are secure.

Tip: Use genuine Craftsman attachments for optimal compatibility.

Mowing Operation

For best results, mow when grass is dry.

Start engine: Engage parking brake, turn key.
Warm up: Allow engine to run for 30 seconds.
Engage blades: Press PTO switch.
Release parking brake: Slowly press drive pedal.
Mow in overlapping passes: For even cutting.
Disengage blades: When stopping or crossing non-grass areas.
Shut down: Engage parking brake, turn key to OFF.

WARNING! Always look behind before backing up. Clear area of debris before mowing.

Safety Features

Operator Presence Control: Engine shuts off if operator leaves seat with blades engaged. Parking Brake: Must be engaged to start engine. Blade Brake Clutch: Stops blades within 3 seconds of disengagement.

Care & Maintenance

Regular maintenance ensures longevity and performance.

Check oil: Before each use, change every 50 hours.
Air filter: Clean every 25 hours, replace annually.
Sharpen blades: Every 25 hours or when cut quality declines.
Battery: Keep terminals clean; charge if not used regularly.
Tires: Maintain proper pressure.
Storage: Use fuel stabilizer for off-season storage.

CAUTION! Disconnect spark plug before performing any maintenance.

Regulatory Information

EPA Certified: Meets emission standards. CARB Compliant: For sale in California. Copyright © 2025 Craftsman; trademarks of Stanley Black & Decker, Inc. For support, visit www.craftsman.com or contact 1-888-331-4569.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Engine won't start	Dead battery, empty fuel, safety switch	Check battery charge; add fuel; ensure parking brake engaged and seat occupied.
Poor cutting performance	Dull blades, low engine speed	Sharpen or replace blades; set throttle to FAST.
Excessive vibration	Unbalanced blade, loose parts	Stop engine, check blade for damage and tightness.
Loss of power	Clogged air filter, old fuel	Clean or replace air filter; drain and replace fuel.
Hydrostatic transmission sluggish	Low fluid, drive belt worn	Check fluid level; inspect and replace drive belt if necessary.

Reset: Turn key to OFF, wait 30 seconds, then restart.

Service: 1-888-331-4569; www.craftsman.com