Craftsman T2400 Riding Lawn Mower Manual

The Craftsman T2400 is a 24-horsepower, 46-inch deck riding lawn mower designed for residential lawn care. It features a Briggs & Stratton engine, hydrostatic transmission, electric start, adjustable cutting height, and a comfortable high-back seat. Below are key sections for safety, features, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Safety Information 3. Assembly & Setup 4. Specifications 5. Controls and Operation 6. Mowing Instructions 7. Maintenance Schedule 8. Storage & Winterization 9. Troubleshooting 10. Warranty Information

Features at a Glance

Key components: 24 HP Briggs & Stratton engine, 46-inch stamped steel cutting deck, Hydrostatic transmission, Electric start, Adjustable high-back seat, Headlights, Cup holder.

Feature	Description
Engine	24 HP Briggs & Stratton, single-cylinder, air-cooled
Cutting Width	46 inches
Transmission	Hydrostatic, foot-pedal controlled
Starting System	Electric key start with backup recoil
Cutting Height	Adjustable 1.5 to 4 inches (6 positions)
Fuel Capacity	3 gallons
Seat	High-back, adjustable suspension
Deck Engagement	Electric PTO (Power Take-Off) lever
Headlights	Two front headlights for low-light operation
Drive System	Rear-wheel drive

Safety Information

Read all instructions before operating. Always wear appropriate safety gear.

Clear mowing area of debris, toys, and obstacles.
Never carry passengers.
Do not mow on slopes greater than 15 degrees.
Disengage blades before crossing driveways or gravel.
Keep hands and feet away from moving parts.

WARNING! Gasoline is flammable; refuel outdoors with engine off and cool. Keep children and pets away during operation.

Assembly & Setup

Unpack and inspect contents. Assembly requires basic tools.

Install steering wheel: Align and tighten bolt.
Attach seat: Mount using provided bolts and washers.
Connect battery: Attach red (+) then black (-) terminals.
Check tire pressure: Inflate to 10 PSI (front) and 12 PSI (rear).
Add engine oil: Use SAE 30 (approx. 2 quarts) to full mark on dipstick.
Add gasoline: Use unleaded 87 octane or higher.

CAUTION! Ensure all bolts are tightened securely. Test operation in a clear, open area.

Specifications

Engine: 24 HP Briggs & Stratton, 724cc.
Cutting Deck: 46-inch stamped steel, 3-blade.
Transmission: Hydrostatic, infinite forward/reverse speeds.
Cutting Height Range: 1.5 to 4 inches.
Fuel Type: Unleaded gasoline (87 octane minimum).
Fuel Capacity: 3 gallons.
Oil Capacity: 2 quarts (SAE 30).
Dimensions (LxWxH): 72 x 54 x 42 inches.
Weight: 550 lbs.
Warranty: 2-year limited warranty.

Controls and Operation

Familiarize yourself with all controls before starting.

Dashboard: Ignition key, PTO (blade engagement) lever, Throttle/Choke, Headlight switch, Hour meter.

Foot Controls: Forward/reverse pedal (hydrostatic drive), Brake pedal.

Steering: Wheel with turning radius of 18 inches.

Starting Procedure: 1. Sit on seat. 2. Set parking brake. 3. Disengage PTO. 4. Move throttle to FAST. 5. Turn key to START. 6. Release key to RUN.

Stopping: Disengage PTO, move throttle to SLOW, engage parking brake, turn key to OFF.

Mowing Instructions

For best results, mow when grass is dry.

Adjust cutting height using deck lift lever.
Start engine and allow to warm up for 30 seconds.
Engage PTO lever to start blades.
Release parking brake and slowly press drive pedal.
Mow in overlapping passes for even cut.
Disengage PTO when crossing non-grass areas.
Empty grass bag when full (if equipped).

Tip: Sharpen blades every 25 hours of use for clean cuts.

Maintenance Schedule

Regular maintenance ensures long life and performance.

Interval	Task
Before each use	Check tire pressure, inspect for loose parts, check oil level
Every 8 hours	Clean underside of deck
Every 25 hours	Change engine oil, sharpen/replace blades, check air filter
Every 50 hours	Replace air filter, check spark plug
Every 100 hours	Change transmission fluid, replace fuel filter
Seasonally	Lubricate pivot points, check battery charge

Note: Refer to engine manual for specific engine maintenance.

Storage & Winterization

Prepare mower for storage if not used for 30+ days.

Add fuel stabilizer to gas tank and run engine for 5 minutes.
Change engine oil and filter.
Remove spark plug, add 1 tablespoon of oil to cylinder, pull starter cord slowly, reinstall plug.
Clean entire mower, especially underside of deck.
Store in a dry, covered area.
Disconnect battery negative terminal if storing longer than 3 months.

CAUTION! Never store with gasoline in tank without stabilizer. Gasoline can degrade and damage fuel system.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Engine won't start	Dead battery, empty fuel, bad spark plug	Charge/replace battery; add fuel; check/replace spark plug.
Engine runs rough	Dirty air filter, old gasoline	Clean/replace air filter; drain old gas and refill with fresh.
Uneven cutting	Dull blades, uneven tire pressure	Sharpen/replace blades; inflate tires to correct PSI.
Loss of power	Clogged deck, dirty fuel filter	Clean underside of deck; replace fuel filter.
Hydrostatic transmission slips	Low transmission fluid	Check fluid level; add recommended fluid if low.

Reset: For safety interlock issues, ensure you are seated, parking brake is set, and PTO is disengaged.

Service: For repairs, contact authorized Craftsman service center or 1-888-331-4569.

Warranty Information

Craftsman T2400 includes a 2-year limited warranty covering defects in materials or workmanship. Warranty does not cover normal wear, misuse, or lack of maintenance. Keep your receipt as proof of purchase. For warranty claims, visit www.craftsman.com or call 1-888-331-4569.