Craftsman T2400 Owners Manual

The Craftsman T2400 is a 24-horsepower lawn tractor featuring a Kohler 7000 Series V-twin engine, hydrostatic transmission with infinite forward/reverse speeds, 46-inch stamped steel mower deck, electric PTO, cruise control, cup holder, and ergonomic high-back seat. Designed for residential lawn care with a cutting height range of 1-4 inches, dual-lever deck lift, and optional bagging system. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly Instructions 3. First-Time Operation 4. Specifications 5. Controls and Settings 6. Attaching Accessories 7. Mowing Operation 8. Safety Features 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: 24 HP Kohler V-twin engine, Hydrostatic transmission, 46-inch mower deck, Electric PTO, Cruise control, Cup holder, High-back seat.

Feature	Description
Engine	24 HP Kohler 7000 Series V-twin, air-cooled
Transmission	Hydrostatic, infinite forward/reverse speeds
Mower Deck	46-inch stamped steel, side discharge
PTO	Electric clutch engagement
Cruise Control	Maintains constant speed without holding pedal
Seat	Ergonomic high-back with armrests
Fuel Tank	3-gallon capacity
Cutting Height	Adjustable 1-4 inches via dual levers
Headlights	Integrated for low-light operation
Drive System	Rear-wheel drive with differential lock

Assembly Instructions

Unpack and inspect contents. Requires basic tools (wrenches, pliers).

Install steering wheel: Align splines, secure with provided nut.
Attach seat: Mount using four bolts and washers.
Connect battery: Attach red (+) then black (-) terminals.
Install mower deck: Lower lift arms, align with pins, secure with retaining clips.
Add engine oil: Use SAE 10W-30, fill to dipstick mark.
Add fuel: Use unleaded gasoline only, fill to 1 inch below neck.

WARNING! Tractor is heavy; use assistance. Ensure all bolts are tightened to specified torque.

First-Time Operation

Perform pre-operation checks before starting.

Check oil level: Ensure dipstick shows full.
Check tire pressure: Inflate to 12 PSI (front) and 10 PSI (rear).
Adjust seat: Position for full pedal reach and clear visibility.
Start engine: Set parking brake, PTO off, turn key to START.
Test controls: Practice forward/reverse, steering, brake engagement.
Engage mower deck: At full throttle, pull PTO switch upward.

CAUTION! Keep hands and feet away from moving parts. Operate only in clear, dry conditions.

Specifications

Engine: 24 HP Kohler 7000 Series V-twin, air-cooled.
Transmission: Hydrostatic, infinite speeds.
Cutting Width: 46 inches.
Cutting Height Range: 1 to 4 inches.
Fuel Capacity: 3 gallons.
Turning Radius: 18 inches.
Weight: 580 lbs.
Warranty: 2-year limited residential warranty.

Controls and Settings

Dashboard: Ignition key, PTO switch, headlight switch, hour meter. Pedals: Forward/reverse pedal, brake pedal. Levers: Deck lift, parking brake.

Operation: Set parking brake before starting. Adjust cutting height via dual levers (1-4 inches). Engage cruise control at desired speed by pushing lever down. Use differential lock for improved traction on slopes.

Maintenance: Check oil every 8 hours; change every 50 hours. Air filter: Clean every 25 hours; replace annually. Blade sharpening: Every 25 hours or when dull.

Attaching Accessories

Supports bagger, mulching kit, snow blade (optional).

Turn off engine and remove key.
Attach bagger: Mount rear bracket, connect chute to deck.
Install mulching kit: Remove discharge chute, install plug and mulching blades.
Mount snow blade: Use front hitch, connect lift rod.

Tip: Refer to accessory manual for specific installation steps.

Mowing Operation

For optimal cutting performance.

Inspect area: Remove debris, rocks, toys.
Adjust cutting height: Set levers to desired height (1-4 inches).
Start mowing: Engage PTO at full throttle, begin overlapping passes.
Use cruise control: Engage on long straightaways.
Empty bagger: When indicator shows full, stop engine and empty.
After mowing: Disengage PTO, let engine idle 30 seconds before shutdown.

WARNING! Do not mow on slopes over 15 degrees. Always mow across slopes, not up/down.

Safety Features

Operator Presence System: Engine stops if leaving seat with PTO engaged. Parking Brake: Must be set to start engine. Blade Brake Clutch: Stops blades within 3 seconds of disengagement.

Care & Maintenance

Regular maintenance ensures longevity.

Daily: Clean deck, check for damage.
Every 8 hours: Check oil, tire pressure.
Every 25 hours: Sharpen blades, clean air filter.
Every 50 hours: Change oil, replace spark plug.
Seasonal: Stabilize fuel, store in dry location.

CAUTION! Disconnect spark plug before performing any maintenance.

Regulatory Information

EPA Certified: Engine meets emission standards. CARB Compliant: For sale in California. Copyright © 2025 Craftsman; trademarks of Stanley Black & Decker, Inc. For support, visit www.craftsman.com or contact 1-888-331-4569.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Engine won't start	Parking brake not set, dead battery	Set parking brake; check battery connections; charge or replace battery.
Poor cutting performance	Dull blades, low engine speed	Sharpen blades; ensure throttle at full speed during mowing.
Excessive vibration	Unbalanced blade, loose deck	Stop engine, check blade balance; tighten deck mounting bolts.
Hydrostatic transmission sluggish	Low fluid, air in system	Check fluid level; purge air per manual instructions.
PTO won't engage	Blown fuse, faulty switch	Check 20-amp fuse; test PTO switch with multimeter.

Reset: Disconnect battery for 5 minutes to reset electrical system.

Service: 1-888-331-4569; www.craftsman.com