Craftsman T2200 Mower Owners Manual

The Craftsman T2200 is a 22-horsepower riding lawn mower with a 46-inch cutting deck, hydrostatic transmission, electric start, and a durable steel frame. Designed for residential use on medium to large lawns, it features a comfortable high-back seat, headlights, cup holder, and a tight 18-inch turning radius. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly Instructions 3. First-Time Setup 4. Specifications 5. Controls and Operation 6. Attachments & Accessories 7. Cutting & Mowing Guide 8. Safety Features 9. Maintenance Schedule 10. Warranty Information 11. Troubleshooting

Features at a Glance

Key components: 22 HP Briggs & Stratton engine, 46-inch stamped steel cutting deck, Hydrostatic transmission, Electric start with key, Comfortable high-back seat, Headlights, Cup holder, Twin headlights.

Feature	Description
Engine	22 HP Briggs & Stratton Intek V-Twin OHV engine
Cutting Deck	46-inch stamped steel, 3-blade system
Transmission	Hydrostatic, foot-pedal controlled
Starting System	Electric key start with 12V battery
Turning Radius	18 inches for tight turns
Seat	Adjustable high-back with armrests
Headlights	Twin headlights for low-light operation
Fuel Capacity	3.5 gallons
Cutting Height	1.5 to 4 inches, 12 positions
Drive System	Rear-wheel drive

Assembly Instructions

Unpack and inspect all parts. Assembly requires basic tools.

Install steering wheel: Align and tighten bolt.
Attach seat: Mount using provided bolts and washers.
Install battery: Connect red (+) then black (-) terminals.
Attach cutting deck: Align with mounting points and secure with pins.
Add engine oil: Use SAE 30 (approx. 2 quarts).
Fill fuel tank: Use fresh unleaded gasoline (87 octane or higher).

WARNING! Mower is heavy; use assistance. Ensure all bolts are tightened securely.

First-Time Setup

Before first use, complete pre-operation checks.

Check tire pressure: Front 14 PSI, Rear 10 PSI.
Adjust seat position: Loosen knob, slide to comfortable position.
Set cutting height: Use lever to desired height (start at 3 inches).
Test controls: Ensure brake, throttle, and blade engage work smoothly.
Start engine: Insert key, set choke, turn to START.

CAUTION! Operate only in clear, dry conditions. Keep area clear of bystanders.

Specifications

Engine: 22 HP Briggs & Stratton Intek V-Twin OHV.
Cutting Width: 46 inches.
Transmission: Hydrostatic, infinite speeds 0-5.5 mph.
Fuel Type: Unleaded gasoline (87 octane minimum).
Fuel Capacity: 3.5 gallons.
Cutting Height Range: 1.5 to 4 inches (12 positions).
Turning Radius: 18 inches.
Weight: 540 lbs (approx.).
Warranty: 2-year limited warranty.

Controls and Operation

Dashboard: Ignition key, Throttle, Choke, Headlight switch, Cup holder. Floor: Forward/reverse pedal, Brake pedal, Blade engage lever.

Operation Steps: 1. Sit on seat. 2. Set parking brake. 3. Engage blade (if mowing). 4. Start engine. 5. Release brake, press pedal to move.

Cutting Height Adjustment: Use lever to select position. Speed Control: Press pedal lightly for slow, fully for fast. Parking: Engage brake, turn key OFF, remove key.

Attachments & Accessories

Compatible with Craftsman attachments: Mulching kit, Bagging system, Snow blade, Tow-behind spreader.

Turn off engine and remove key before attaching.
Follow attachment-specific instructions.
Ensure all pins and locks are secure.

Tip: Use only Craftsman-approved attachments to avoid damage.

Cutting & Mowing Guide

For best results, follow these mowing practices.

Mow when grass is dry.
Overlap passes by 2-3 inches.
Change mowing pattern each time.
Adjust height seasonally: higher in summer, lower in spring/fall.
Sharp blades: Dull blades tear grass; sharpen annually.
Discharge chute: Always point away from people, buildings, roads.

WARNING! Never mow on slopes greater than 15 degrees. Watch for hidden obstacles.

Safety Features

Operator Presence System: Engine stops if operator leaves seat with blade engaged. Blade Brake Clutch: Stops blades within 3 seconds when disengaged. Parking Brake: Locks rear wheels. Safety Interlock: Prevents starting unless brake engaged and blade disengaged.

Maintenance Schedule

Regular maintenance ensures long life and safe operation.

Interval	Task
Before each use	Check tire pressure, fuel level, blade condition
Every 8 hours	Check engine oil level
Every 25 hours	Change engine oil, check air filter
Every 50 hours	Sharpen blades, grease fittings
Every 100 hours	Replace spark plug, check battery
Season end	Drain fuel or add stabilizer, clean deck

CAUTION! Always disconnect spark plug wire before performing maintenance.

Warranty Information

Craftsman T2200 includes a 2-year limited warranty covering defects in materials and workmanship. Warranty does not cover normal wear, misuse, or lack of maintenance. For warranty service, contact Craftsman Customer Support at 1-888-331-4569 or visit www.craftsman.com. Keep your receipt and model number (model 247.289520) for reference.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Engine won't start	Dead battery, empty fuel, safety interlock	Charge battery, add fuel, ensure brake engaged and blade off.
Poor cutting quality	Dull blades, low engine speed	Sharpen blades, set throttle to FULL.
Loss of power	Clogged air filter, old fuel	Clean/replace air filter, drain old fuel.
Hydrostatic transmission sluggish	Low fluid, drive belt worn	Check fluid level, inspect belt for wear.
Vibration	Unbalanced blade, loose parts	Balance or replace blade, tighten bolts.

Reset: Turn key OFF, wait 30 seconds, restart.

Service: 1-888-331-4569; www.craftsman.com