Craftsman T200 and T300 Parts Manuals

The Craftsman T200 and T300 series are popular riding lawn mowers known for their reliability and performance. These parts manuals provide detailed diagrams, part numbers, and ordering information for all components of the T200 and T300 models, including the engine, deck, transmission, electrical system, and chassis. Below are key sections covering model identification, parts lookup, diagrams, ordering, and maintenance.

Model Identification & Serial Numbers

Locate your model and serial number to ensure correct parts ordering. Key locations: under the seat, on the frame near the rear axle, or on the engine housing.

Model Series	Description
T200	42-inch or 46-inch deck, 19.5 HP engine, automatic transmission
T300	46-inch or 54-inch deck, 24 HP engine, enhanced transmission
Serial Number Format	Example: 123456X (First digits indicate year/week of manufacture)
Engine Model	Kohler 7000 Series or Briggs & Stratton Intek
Deck Size	Measured in inches (cutting width)

Engine Parts (Kohler/ Briggs & Stratton)

Detailed parts breakdown for the engine assembly. Includes air filter, oil filter, spark plugs, carburetor, starter, and ignition components.

1. Cylinder & Piston: Piston rings, connecting rod, gaskets.
2. Fuel System: Carburetor kit, fuel pump, fuel lines, fuel filter.
3. Ignition System: Spark plug, ignition coil, flywheel key.
4. Lubrication: Oil filter, dipstick, oil drain tube.
5. Cooling: Cooling fins, blower housing, fan.

WARNING! Disconnect spark plug wire before servicing engine. Use correct oil type and grade.

Cutting Deck Assembly

Parts for the mower deck including blades, spindles, belts, and housing.

1. Deck Shell: Main housing, skid shoes, deck hangers.
2. Blades: Standard and high-lift blades (part numbers vary by deck size).
3. Spindles: Spindle assembly, bearings, pulley.
4. Belt: Deck drive belt (length specific to deck size).
5. Deck Wheels: Anti-scalp wheels and hardware.

CAUTION! Ensure deck is securely supported and engine off before replacing blades or belts.

Specifications

• Engine Options: Kohler 7000 Series 19.5HP-24HP; Briggs & Stratton Intek.
• Transmission: T200: Automatic; T300: Enhanced automatic with optional cruise control.
• Cutting Width: 42", 46", or 54" (model dependent).
• Fuel Capacity: 2.5 gallons (approx).
• Oil Capacity: 1.5-2 quarts (check dipstick).
• Battery: 12V, 280 CCA.
• Tire Size Front: 15x6.00-6.
• Tire Size Rear: 20x10.00-8.
• Weight: Approx. 500 lbs (varies by configuration).

Transmission & Drive System

Components for the drive system including transmission, drive belt, pulleys, and linkage.

Transmission: Peerless 2000 series (T200) / 3100 series (T300). Includes input shaft, output shaft, seals, and fluid.

Drive Belt: Main drive belt (connects engine to transmission).

Pulleys: Idler pulleys, engine pulley, transmission pulley.

Linkage: Shift linkage, brake linkage, pedal assemblies.

Fluid: Transmission fluid type and capacity (refer to manual).

Electrical System & Wiring

Wiring harness, battery, starter, solenoid, switches, and lights.

1. Turn off engine and remove key before servicing electrical components.
2. Check battery connections for corrosion.
3. Refer to wiring diagram for proper wire routing and connections.

Key Components: Battery, starter motor, ignition switch, safety interlock switches, headlight (if equipped), voltage regulator.

Chassis, Steering & Tires

Frame, steering column, tie rods, front axle, and wheel assemblies.

1. Frame: Main frame, footrests, seat mounting plate.
2. Steering: Steering wheel, column, gear, tie rod ends.
3. Front Axle: Axle pivot, bushings, spindle arms.
4. Tires & Wheels: Front and rear tires, wheels, valve stems.
5. Brakes: Brake disc, caliper, brake rod.

Tip: Lubricate steering and pivot points regularly for smooth operation.

Belts, Pulleys & Spindles

Detailed listing of all belts and pulley configurations for deck and drive systems.

1. Deck Belt: Part number varies by deck size (42", 46", 54").
2. Drive Belt: Single belt for engine to transmission.
3. Idler Pulleys: Spring-loaded and fixed idlers.
4. Spindle Assemblies: Complete spindle or individual bearings and housings.
5. Blade Mandrel: Spindle shaft and hardware.

WARNING! Always replace with OEM-specified belts. Incorrect length can cause damage or poor performance.

Safety & Control Components

Safety switches, control cables, pedals, and levers.

Safety Interlock System: Seat switch, brake switch, PTO switch, ignition switch.

Control Cables: Throttle cable, choke cable, PTO engagement cable.

Pedals: Brake pedal, clutch/brake pedal assembly, drive pedal.

Levers: Deck height adjustment lever, parking brake lever.

Maintenance Parts & Filters

Regular maintenance items: air filter, oil filter, fuel filter, spark plug, blades, belts, lubricants.

Air Filter: Part number for paper and pre-filter foam.

Oil Filter: Spin-on type (cross-reference to common brands).

Fuel Filter: In-line fuel filter.

Spark Plug: Champion RC12YC or equivalent.

Lubricants: SAE 30 or 10W-30 engine oil; 20W-50 transmission fluid (if applicable).

CAUTION! Follow recommended service intervals. Use only specified filters and fluids.

Parts Ordering & Warranty

How to order genuine Craftsman parts and warranty information.

Source	Contact/Website	Notes
Craftsman Parts Direct	www.craftsman.com/parts	Enter model and serial number for diagrams
Authorized Service Centers	Locator on website	Professional installation available
Customer Support	1-888-331-4569	For parts identification and ordering help

Warranty: Limited warranty on parts (duration varies). Keep proof of purchase.

Returns: Unused parts in original packaging may be returned within 30 days.

Troubleshooting & Common Replacements

Symptom	Possible Cause	Common Replacement Parts
Engine won't start	Bad battery, faulty solenoid, dead spark plug	Battery, solenoid, spark plug
Poor cutting performance	Dull blades, worn deck belt, damaged spindle	Blades, deck belt, spindle assembly
Transmission slips/no drive	Worn drive belt, low fluid, internal wear	Drive belt, transmission fluid, input shaft
Excessive vibration	Unbalanced blade, bent spindle, loose pulley	Blade, spindle, pulley hardware
Electrical issues (no lights/crank)	Blown fuse, corroded connections, bad switch	Fuses, wiring harness, ignition switch

Note: Always consult the full service manual for detailed repair procedures.

Support: 1-888-331-4569 | www.craftsman.com