Craftsman T110 42-in Riding Mower User Manual

The Craftsman T110 is a 42-inch deck riding lawn mower featuring a 19.5 HP Briggs & Stratton engine, 6-speed manual transmission, electric start, adjustable cutting height (1.5-4 inches), mulching/bagging/side discharge capabilities, ergonomic high-back seat, cup holder, and LED headlights. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Setup 3. First-Time Operation 4. Specifications 5. Controls and Settings 6. Attachments & Accessories 7. Mowing Operation 8. Safety Features 9. Maintenance & Storage 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: 42-inch stamped steel cutting deck, 19.5 HP engine, 6-speed transmission, electric start, high-back seat, cup holder, headlights.

Feature	Description
Cutting Width	42 inches
Engine	19.5 HP Briggs & Stratton, single-cylinder
Transmission	6-speed manual gear drive
Starting System	Electric key start
Cutting Height	Adjustable 1.5-4 inches (6 positions)
Deck Material	Stamped steel
Seat	Ergonomic high-back with armrests
Fuel Capacity	2.5 gallons
Headlights	LED for low-light operation
Drive System	Rear-wheel drive

Assembly & Setup

Unpack and inspect contents. Assembly requires basic tools.

Install steering wheel: Align and secure with provided hardware.
Attach seat: Bolt seat to frame using included bolts and washers.
Install battery: Connect red (+) then black (-) terminals.
Attach cutting deck: Lower deck onto mounting points and secure with pins.
Add engine oil and fuel: Use SAE 30 oil (check manual) and unleaded gasoline.

WARNING! Mower is heavy; use assistance during assembly. Ensure all bolts are tightened securely.

First-Time Operation

Perform pre-operation checks before starting.

Check oil level: Use dipstick; add if below full mark.
Check fuel: Fill with fresh unleaded gasoline.
Adjust seat: Position for comfortable reach to controls.
Set cutting height: Use lever to desired height.
Start engine: Insert key, set parking brake, engage blade control, turn key.
Practice operation: In open area without blade engaged.

CAUTION! Never operate without checking for obstacles or debris in mowing area.

Specifications

Model: Craftsman T110
Cutting Width: 42 inches
Engine: 19.5 HP Briggs & Stratton, OHV
Transmission: 6-speed manual
Fuel Type: Unleaded gasoline (87 octane or higher)
Fuel Capacity: 2.5 gallons
Oil Capacity: 1.5 quarts (SAE 30)
Cutting Height Range: 1.5-4 inches
Turning Radius: 18 inches
Weight: 450 lbs

Controls and Settings

Dashboard: Ignition key, headlight switch, hour meter. Floor: Brake pedal, clutch/brake pedal, gear shift lever. Deck controls: Cutting height lever, blade engagement lever.

Operation Controls: Steering wheel, throttle lever, parking brake lever, cup holder.

Settings: Cutting height (lever adjustment), throttle (fast/slow), parking brake (engage/disengage). Safety: Blade must be disengaged to start; seat safety switch stops blade if operator leaves seat.

Attachments & Accessories

Optional: Mulching kit, bagger system, tow-behind spreader.

Mulching kit: Install blades and plug for fine clippings.
Bagger: Attach chute and bagger assembly to rear.
Spreader: Hitch to tow bar; follow weight limits.

Tip: Ensure engine is off and key removed before attaching accessories.

Mowing Operation

Supports standard mowing, mulching, bagging, side discharge.

Start: Engage parking brake, disengage blade, turn key.
Select gear: Start in 1st gear; shift as needed.
Engage blade: Pull lever slowly to engage cutting blades.
Mow patterns: Overlap passes by 2-3 inches for even cut.
Adjust speed: Use throttle for consistent cutting.
Disengage blade: When stopping or crossing non-grass areas.
Shut down: Disengage blade, set parking brake, turn key off.

WARNING! Keep hands and feet away from moving parts. Do not mow on slopes over 15 degrees.

Safety Features

Blade Brake Clutch: Stops blade within 3 seconds when disengaged. Seat Safety Switch: Stops blade if operator leaves seat. Parking Brake: Must be engaged to start engine.

Maintenance & Storage

Perform regular maintenance for optimal performance.

Daily: Check tire pressure, clean deck after use.
Every 25 hours: Change oil, check air filter.
Every 50 hours: Sharpen blades, check spark plug.
Seasonal: Lubricate moving parts, store with stabilized fuel.

CAUTION! Disconnect spark plug before performing maintenance. Store in dry, covered area.

Regulatory Information

EPA Certified: Engine meets emission standards. Safety Compliance: ANSI/OPEI B71.1-2017. Copyright © 2023 Craftsman; trademarks of Stanley Black & Decker, Inc. For support, visit www.craftsman.com or contact 1-888-331-4569.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Engine won't start	Battery/ fuel/ safety switch	Check battery charge; ensure parking brake engaged; verify fuel level.
Poor cutting performance	Dull blades/ deck clog	Sharpen or replace blades; clean underside of deck.
Excessive vibration	Unbalanced blade/ loose parts	Check blade balance; tighten deck bolts and mounting hardware.
Loss of power	Clogged air filter/ old fuel	Replace air filter; drain old fuel and refill with fresh gasoline.
Hard to shift gears	Transmission fluid/ linkage	Check transmission fluid level; lubricate shift linkage.

Reset: Turn key off and wait 30 seconds if safety switch triggers.

Service: 1-888-331-4569; www.craftsman.com