Craftsman T 110 Manual

The Craftsman T 110 is a 42-inch riding lawn tractor designed for residential use, featuring a 19.5 HP Briggs & Stratton engine, 6-speed manual transmission, electric start, 3-in-1 cutting system (mulch, bag, side discharge), adjustable cutting height (1.5-4 inches), and a 2-gallon fuel tank. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: 19.5 HP engine, 6-speed transmission, 42-inch cutting deck, electric start, adjustable seat, cup holder, headlights.

Feature	Description
Engine	19.5 HP Briggs & Stratton single-cylinder OHV
Transmission	6-speed manual shift-on-the-go
Cutting Width	42-inch stamped steel deck
Cutting Height	Adjustable 1.5 to 4 inches (6 positions)
Fuel Tank	2-gallon capacity
Starting System	Electric key start with backup recoil
Seat	High-back with armrests, adjustable fore/aft
Headlights	Integrated for low-light operation
Drive System	Rear-wheel drive with differential lock
Blade Engagement	Electric PTO (Power Take-Off) switch

Assembly Instructions

Unpack and inspect all parts. Assembly requires basic tools.

1. Install steering wheel: Align and tighten bolt.
2. Attach seat: Mount using provided bolts and washers.
3. Connect battery: Attach red (+) then black (-) cables.
4. Install cutting deck: Lower deck lift, align with pins, secure with retaining clips.
5. Add fuel: Use fresh unleaded gasoline (87 octane minimum).

WARNING! Tractor is heavy; use assistance. Ensure all bolts are tightened to specification.

First-Time Operation

Perform pre-operation checks before starting.

1. Check oil level: Use dipstick, add SAE 30 if needed.
2. Check tire pressure: Front 14 PSI, rear 10 PSI.
3. Adjust seat: Position for full pedal and control reach.
4. Start engine: Insert key, set parking brake, press brake, turn to START.
5. Test controls: Practice steering, braking, and blade engagement in safe area.

CAUTION! Never operate on slopes greater than 15 degrees. Keep hands and feet away from moving parts.

Specifications

• Engine: 19.5 HP Briggs & Stratton, OHV, single-cylinder.
• Transmission: 6-speed manual, shift-on-the-go.
• Cutting Deck: 42-inch stamped steel, 3-in-1 capability.
• Cutting Height: 1.5 to 4 inches (6 positions).
• Fuel Capacity: 2 gallons unleaded.
• Dimensions: 68" L x 42" W x 46" H.
• Weight: 450 lbs (approx).
• Tires: Front 15x6.00-6, Rear 20x10.00-8.
• Warranty: 2-year limited residential warranty.

Controls and Settings

Dashboard: Ignition key, PTO switch, throttle, choke, hour meter. Floor: Brake pedal, clutch/brake pedal, gear shift lever.

Steering: Tilt wheel, turning radius 18 inches. Cutting Height: Adjust via deck lift lever (positions 1-6). Seat: Adjust fore/aft with lever. Parking Brake: Engage by pressing brake pedal fully and setting latch.

Operation: Start with brake depressed, PTO off. Engage blades only when moving forward. Use slower speeds on slopes.

Attaching Accessories

Compatible with Craftsman mulch kit, bagger, and tow-behind spreader.

1. Turn off engine and remove key.
2. For bagger: Attach chute to deck outlet, connect bags to frame.
3. For mulch kit: Install mulch plug and blade.
4. For tow spreader: Hitch to rear drawbar, secure with pin.

Tip: Ensure all attachments are securely fastened before operation.

Mowing Operations

For best results, mow when grass is dry.

1. Set cutting height: Adjust lever to desired position.
2. Start mower: Engage PTO switch after engine is running.
3. Mow patterns: Overlap passes by 2-3 inches for even cut.
4. Slope mowing: Mow up and down, not across, on slopes under 15 degrees.
5. Discharge: Direct clippings away from buildings and roads.
6. Clean deck: After use, raise deck and clean underside.

WARNING! Never remove grass catcher or unclog chute with engine running. Watch for obstacles.

Safety Features

Operator Presence System: Engine stops if leaves seat with PTO engaged. Parking Brake: Must be set to start engine. Blade Brake Clutch: Stops blades within 7 seconds when disengaged.

Care & Maintenance

Regular maintenance ensures long life.

• After each use: Clean deck, check for damage.
• Every 25 hours: Change oil, check air filter.
• Every 50 hours: Sharpen blades, check tire pressure.
• Every 100 hours: Replace spark plug, check belts.
• Storage: Drain fuel or add stabilizer, disconnect battery.

CAUTION! Always disconnect spark plug wire before performing maintenance.

Regulatory Information

EPA Certified Engine: Meets emission standards. CARB Compliant: For sale in California. Copyright © 2025 Craftsman; trademarks of Stanley Black & Decker, Inc. For support, visit www.craftsman.com or contact 1-888-331-4569.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Engine won't start	Battery, fuel, safety switch	Check battery charge; ensure fuel valve on; sit firmly in seat; check brake engaged.
Loss of power	Clogged filter, old fuel	Replace air filter; drain old fuel; check spark plug.
Uneven cutting	Deck level, dull blades	Level deck; sharpen or replace blades.
Excessive vibration	Loose blade, debris	Tighten blade bolt; clean deck of debris.
Won't move	Transmission, drive belt	Check gear shift in position; inspect drive belt for wear.

Reset: Turn key off and wait 2 minutes if safety system engages.

Service: 1-888-331-4569; www.craftsman.com