Craftsman Riding Lawn Mower T210 Manual

The Craftsman T210 is a 42-inch riding lawn mower featuring a 19.5 HP Briggs & Stratton engine, hydrostatic transmission, 6-speed gear drive, electric start, cruise control, adjustable cutting height (1.5-4 inches), mulching capability, and a 2.5-gallon fuel tank. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Setup 3. Controls and Operation 4. Specifications 5. Maintenance Schedule 6. Cutting Deck Adjustment 7. Storage & Winterization 8. Safety Information 9. Warranty & Support 10. Troubleshooting

Features at a Glance

Key components: 19.5 HP engine, 42-inch steel cutting deck, hydrostatic transmission, electric start, cruise control, adjustable seat, cup holder, and LED headlights.

Feature	Description
Engine	19.5 HP Briggs & Stratton, single-cylinder, OHV
Cutting Width	42 inches
Transmission	Hydrostatic, single pedal control
Cutting Height	Adjustable from 1.5 to 4 inches (6 positions)
Fuel Tank	2.5 gallons
Starting System	Electric key start with backup recoil
Deck Engagement	Electric PTO (Power Take-Off) lever
Speed Control	Forward/reverse pedal with cruise control
Mulching	Mulch-ready deck with plug-in capability
Headlights	LED headlights for low-light operation

Assembly & Setup

Unpack and inspect all parts. Assembly requires basic tools.

Install steering wheel: Align and tighten bolt.
Attach seat: Mount using provided bolts and washers.
Install battery: Connect red (+) then black (-) terminals.
Attach cutting deck: Lower deck onto mounting points and secure with pins.
Add engine oil and fuel: Use SAE 30 oil (check dipstick) and unleaded gasoline.

WARNING! Wear gloves during assembly. Ensure all bolts are tightened securely. Keep hands clear of cutting blades.

Controls and Operation

Familiarize yourself with controls before starting.

Pre-start check: Oil level, fuel, tire pressure, and clear area.
Starting: Sit on seat, set parking brake, turn key to START.
Driving: Release parking brake, press forward pedal to move.
Engage blades: Pull PTO lever upward at desired mowing speed.
Stopping: Disengage PTO, set parking brake, turn key OFF.

CAUTION! Always engage parking brake on slopes. Do not mow on slopes greater than 15 degrees.

Specifications

Engine: 19.5 HP Briggs & Stratton, OHV
Cutting Deck: 42-inch stamped steel
Transmission: Hydrostatic, infinite speeds 0-5.5 mph
Fuel Capacity: 2.5 gallons
Cutting Height Range: 1.5 - 4 inches (6 positions)
Tire Size (Front): 15 x 6.00-6
Tire Size (Rear): 20 x 10.00-8
Weight: 450 lbs (approx.)
Warranty: 2-year limited warranty

Maintenance Schedule

Regular maintenance ensures optimal performance and longevity.

Interval	Task
Before each use	Check oil level, tire pressure, fuel
Every 8 hours	Check blade condition, deck for debris
Every 50 hours	Change engine oil, check air filter
Every 100 hours	Replace spark plug, sharpen blades
Seasonally	Lubricate moving parts, check battery

Tip: Always disconnect spark plug wire before performing maintenance.

Cutting Deck Adjustment

Adjust cutting height to match grass conditions.

Park on level surface, engage parking brake, turn off engine.
Locate adjustment lever on left side of deck.
Move lever to desired height setting (1-6).
Ensure all wheels are at same height for even cut.

WARNING! Never adjust deck while engine is running. Keep hands away from blades.

Storage & Winterization

Prepare mower for long-term storage.

Clean deck thoroughly to remove grass and debris.
Change engine oil and run engine briefly to circulate.
Add fuel stabilizer to tank and run for 5 minutes.
Disconnect battery and store in cool, dry place.
Store in covered, dry area away from moisture.

CAUTION! Never store with fuel in tank without stabilizer. Drain fuel if storing over 30 days.

Safety Information

Always follow safety guidelines to prevent injury.

Wear eye protection, long pants, and sturdy shoes.
Clear mowing area of debris, toys, and obstacles.
Never carry passengers.
Do not mow on steep slopes (max 15 degrees).
Keep hands and feet away from moving parts.
Always engage parking brake when stopped.

DANGER! Rotating blades can cause severe injury. Always turn off engine and remove key before servicing.

Warranty & Support

Craftsman T210 includes 2-year limited warranty covering defects in materials and workmanship. Warranty does not cover normal wear, misuse, or lack of maintenance. For support, contact Craftsman Customer Service at 1-888-331-4569 or visit www.craftsman.com. Keep original receipt for warranty claims.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Engine won't start	Dead battery, empty fuel, clogged filter	Charge battery, add fuel, check air filter
Poor cutting performance	Dull blades, low engine speed	Sharpen blades, check throttle setting
Vibration during operation	Unbalanced blade, debris in deck	Inspect and balance blade, clean deck
Loss of power	Dirty air filter, old spark plug	Replace air filter and spark plug
Hydrostatic transmission issues	Low fluid, drive belt worn	Check fluid level, inspect drive belt

Reset: Disconnect battery for 5 minutes to reset electrical system if needed.

Service: 1-888-331-4569; www.craftsman.com