The Craftsman Model 917 is a versatile lawn and garden tractor known for its durability and performance. This manual provides detailed parts diagrams, exploded views, and part numbers for the Model 917 series, including the engine, transmission, mower deck, electrical system, and chassis components. Use this guide for identification, ordering, and assembly of genuine Craftsman replacement parts to ensure proper maintenance and repair.
This manual is intended for use by qualified technicians and experienced owners. Always follow safety precautions when servicing your Craftsman Model 917.
| Safety Symbol | Meaning |
|---|---|
| ⚠️ | Warning - Risk of personal injury or equipment damage |
| 🔧 | Tools Required |
| 📋 | Reference to another diagram or section |
| 🔌 | Disconnect spark plug before servicing |
| ⚙️ | Torque specification required |
Locate your model and serial number plate, typically found on the frame under the seat or on the dash. This ensures you reference the correct parts diagrams.
IMPORTANT! Always verify your exact model number before ordering parts. Using incorrect parts may cause equipment failure or safety hazards.
Complete exploded view of the engine assembly with part numbers for all components.
Parts diagram for the transmission, drive shaft, axles, and related components.
Transmission Type: Peerless 5-speed manual or Hydrostatic
Key Components: Input shaft, gears, shift forks, output shaft, differential, axle housings, bearings, seals.
Part Numbers: Transmission Assembly # 901234X, Drive Belt # 012345X, Axle # 135790X, Bearing # 246801X.
Exploded view of the cutting deck, blades, spindles, belts, and mounting hardware.
WARNING! Always disconnect spark plug and ensure blades are stopped before servicing deck.
Wiring diagram and parts for battery, ignition, lights, switches, and sensors.
| Component | Part Number | Description |
|---|---|---|
| Battery | # 987654X | 12V, 280 CCA |
| Starter Solenoid | # 876543X | 12V continuous duty |
| Ignition Switch | # 765432X | Key start with positions |
| Voltage Regulator | # 654321X | For charging system |
| Headlight Assembly | # 543210X | Left/right with bulb |
| Safety Switch | # 432109X | Seat, brake, PTO |
| Wiring Harness | # 321098X | Main harness assembly |
Frame, steering gear, front axle, tires, and wheel components.
Frame Assembly: Part # 210987X. Front Axle: Part # 109876X. Steering Wheel: Part # 098765X. Tie Rods: Part # 987654X. Front Wheel Assembly: Part # 876543X. Rear Wheel Assembly: Part # 765432X. Tires: 20x10-8 rear, 16x6.50-8 front.
Tip: Check wheel bearings and steering linkage for wear during routine maintenance.
Parts for throttle, choke, PTO lever, brake pedal, and optional attachments.
WARNING! Ensure all controls move freely and return to neutral when released.
Reference for bolts, nuts, washers, pins, and clips used throughout the tractor.
How to order genuine Craftsman parts using this manual.
CAUTION! Use only genuine Craftsman or approved equivalent parts to maintain warranty and safety.
| Step | Procedure | Torque Spec (ft-lbs) |
|---|---|---|
| 1. Engine Mounting | Install engine to frame with isolators | 25-30 |
| 2. Deck Installation | Attach deck to lift linkage and secure | 18-22 |
| 3. Drive Belt Routing | Route belt per diagram; tension idler | N/A |
| 4. Wheel Installation | Mount wheels with lugs and washers | 40-45 |
| 5. Control Linkage | Connect throttle, choke, PTO cables | Adjust to spec |
| 6. Electrical Connections | Connect battery, solenoid, switches | Secure all terminals |
Final Check: Verify all fasteners are tight, fluids are filled, and safety systems operate before starting.
Support: For technical assistance, contact Craftsman Customer Service at 1-888-331-4569 or visit www.craftsman.com.