Craftsman High Wheel Trimmer Parts Manual

The Craftsman High Wheel Trimmer is a durable, professional-grade lawn maintenance tool designed for efficient trimming and edging. This manual provides detailed parts identification, assembly instructions, maintenance procedures, and troubleshooting guidance for your high wheel trimmer model. Below are key sections covering parts diagrams, specifications, operation, maintenance, and safety information.

1. Parts Identification & Diagrams 2. Specifications 3. Assembly Instructions 4. Operation & Controls 5. Maintenance Schedule 6. Blade & Line Replacement 7. Engine Care 8. Safety Precautions 9. Troubleshooting 10. Warranty & Support

Parts Identification & Diagrams

Key components: High wheel assembly, Cutting head, Engine, Handle assembly, Drive system, Fuel tank, and Safety guards.

Part Number	Description	Quantity
CM-1001	High Wheel (21-inch)	2
CM-1002	Cutting Head Assembly	1
CM-1003	4-Cycle Engine (190cc)	1
CM-1004	Adjustable Handlebar	1
CM-1005	Drive Belt	1
CM-1006	Fuel Tank (1.2 gal)	1
CM-1007	Safety Guard	1
CM-1008	Throttle Control Cable	1
CM-1009	Wheel Axle Pin	2
CM-1010	Cutting Line Spool (0.095")	1

Specifications

Engine: 190cc 4-cycle OHV, air-cooled.
Cutting Width: 22 inches.
Wheel Size: 21-inch pneumatic tires.
Drive System: Belt-driven with engagement lever.
Fuel Capacity: 1.2 gallons (unleaded gasoline).
Cutting Options: Dual-line trimmer head and optional blade attachment.
Handle: Adjustable height with padded grips.
Weight: 95 lbs (assembled).
Warranty: 2-year limited warranty.

Assembly Instructions

Unpack all parts and verify against packing list. Assembly requires basic tools (wrenches, screwdriver).

Attach wheels: Slide axle through frame, secure with axle pins and washers.
Install handlebar: Align with mounting brackets, secure with provided bolts.
Mount cutting head: Align with drive shaft, secure locking bolt.
Connect controls: Route throttle cable to engine, attach to handle lever.
Install safety guard: Secure over cutting head with screws.
Add fuel and oil: Use unleaded gasoline and SAE 30 oil (check engine manual).

WARNING! Do not attempt assembly without proper tools. Ensure all fasteners are tight before operation.

Operation & Controls

Controls located on handle: Throttle lever, Drive engagement lever, Engine choke, Primer bulb, Stop switch.

Starting Procedure:

Move to clear, flat area.
Set choke to "COLD START" if engine is cold.
Press primer bulb 5 times.
Pull starter cord firmly until engine starts.
Adjust choke to "RUN" after engine warms.

Operation: Squeeze throttle to increase engine speed. Engage drive lever to rotate cutting head. Release to stop.

Maintenance Schedule

Interval	Task
Before each use	Check fuel level, inspect cutting head, test controls
Every 25 hours	Check air filter, inspect drive belt tension
Every 50 hours	Change engine oil, sharpen/replace blade
Every 100 hours	Replace spark plug, inspect wheel bearings
Season end	Drain fuel, clean entire unit, store indoors

Note: Refer to engine manual for specific engine maintenance.

Blade & Line Replacement

Trimmer Line Replacement:

Stop engine and disconnect spark plug wire.
Remove spool cover by turning counterclockwise.
Remove old line, wind new line (0.095" diameter) following arrow direction.
Reinstall spool, ensuring line feeds freely.

Blade Replacement:

Use wrench to remove blade bolt (clockwise to loosen).
Replace with approved Craftsman blade.
Tighten bolt securely (40-45 ft-lbs torque).

CAUTION! Always wear heavy gloves when handling cutting blades.

Engine Care

4-cycle engine requires separate oil and fuel.

Oil Change: Run engine to warm, drain via plug, refill with SAE 30 (20 oz capacity).
Air Filter: Clean foam filter every 25 hours with soapy water, dry thoroughly.
Spark Plug: Gap at 0.030", replace annually.
Fuel: Use fresh unleaded gasoline (87 octane minimum). Add fuel stabilizer for storage.

WARNING! Never run engine without proper oil level.

Safety Precautions

Always wear safety glasses, gloves, long pants, and sturdy shoes.
Clear work area of debris, rocks, and bystanders before operation.
Never operate on steep slopes (over 15 degrees).
Keep hands and feet away from cutting head while engine is running.
Disconnect spark plug before performing any maintenance.
Use only Craftsman-approved replacement parts.

DANGER! Rotating blades can cause serious injury. Always follow safety guidelines.

Troubleshooting

Problem	Possible Cause	Solution
Engine won't start	Empty fuel tank, clogged fuel line, faulty spark plug	Refill fuel, clean fuel line, check/replace spark plug
Loss of power	Dirty air filter, old fuel, dull blade	Clean/replace air filter, use fresh fuel, sharpen blade
Vibration	Loose blade or wheel, unbalanced cutting head	Tighten all fasteners, balance cutting head
Line not feeding	Tangled spool, worn line	Replace spool, ensure proper line winding
Wheels not turning	Loose drive belt, engaged brake	Adjust belt tension, release drive lever

Warranty & Support

Craftsman High Wheel Trimmer comes with a 2-year limited warranty covering defects in materials and workmanship. Warranty does not cover normal wear, misuse, or improper maintenance.

Parts Ordering: Use part numbers from this manual when ordering replacements.

Customer Support: 1-888-331-4569

Online: www.craftsman.com/parts

Service Centers: Visit website for authorized service locations.